Seismic fragility of suspended ceiling systems used in NZ based on component tests

Abstract

Current standards and guidelines for the design and installation of perimeter-fixed suspended ceilings are briefly reviewed and a summary of common damage in recent earthquakes is provided. Component failure fragility curves have been derived following experiments on typical NZ suspended ceilings, considering loading in tension, compression and shear. A simple method to analyse perimeter-fixed ceilings using peak floor acceleration (PFA) is described, allowing for ceiling system fragility to be obtained from component fragilities. This is illustrated in an example of a 5 storey building. It was found that single rivet end-fixings and cross-tee connections were the most critical elements of the ceilings governing the system capacity. In the design examples it was shown that ceilings at different elevations of the structure showed different probabilities of failure and larger ceiling areas with heavier tiles were most susceptible to damage.

References

Taghavi S and Miranda E (2003). “Response Assessment of Non-structural Building Elements”. Report PEER 2003/05, Pacific Earthquake Engineering Research Center, University of California, Berkeley, USA, 96 pp.

MacRae GA and Lehman D (2001). “Chapter 4, Buildings”, in “The Nisqually Washington Earthquake, February 28, 2001 Preliminary Reconnaissance Report”. Co-authored by the Nisqually Earthquake Clearinghouse Group, University of Washington, Seattle. Earthquake Engineering Research Institute, EERI Learning from Earthquakes Project, USA.

Dhakal RP (2010). “Damage to Non-Structural Components and Contents in 2010 Darfield Earthquake”. Bulletin of the New Zealand Society for Earthquake Engineering, 43(4): 404-411.

MacRae GA, Pampanin S, Dhakal R, Palermo A, Baird A and Tasligedik S (2012). “Review of Design and Installation Practices for Non-Structural Components”, Report prepared for the Engineering Advisory Group of the Department of Building and Housing by New Zealand Consultants, Industry and Related Experts, NZ, June 2012.

Bradley B, Dhakal R, MacRae G and Cubrinovski M (2010). “Prediction of Spatially Distributed Seismic Demands in Specific Structures: Structural Response to Loss Estimation". Earthquake Engineering and Structural Dynamics, 39(6), 591-613.

Ferner H, Wemyss M, Baird A, Beer A and Hunter D (2014). “Seismic performance of non-structural elements within buildings”. Proceedings of New Zealand Society of Earthquake Engineering (NZSEE) Conference, Auckland, NZ, 21-23 March 2014.

Masato Motosakaa and Kazuya Mitsujib (2012). “Building Damage during the 2011 off the Pacific Coast of Tohoku Earthquake”. Journal of Soils and Foundations, 52(5): 929–944. DOI: https://doi.org/10.1016/j.sandf.2012.11.012

Nation Media (2011). http://www.nationmultimedia.com/headlines/At-least-20-dead-after-8-8-magnitude-tremor-30150675.html.

FEMA E74 (2011). “Reducing the Risks of Non-Structural Earthquake Damage – A Practical Guide”. Washington D.C., USA.

USG Australia (2012). “Generic Seismic Design for USG DONN Exposed Grid Suspended Ceilings”. Auckland, New Zealand.

American Society for Testing and Materials International (2011). “E580/E580M-11b 2011.Standard Practice for Installation of Ceiling Suspension Systems for Acoustical Tile and Lay-in Panels in Areas Subject to Earthquake Ground Motions”. PA, USA.

Australian/New Zealand Standard (2000). “AS/NZS 2785:2000 Suspended ceilings - Design and Installation”. Standards New Zealand, Wellington, NZ.

USG Australia (2011). “DONN Brand Grid Suspension System”. USG Australia, Auckland, NZ.

Rondo (2008). “DUO Two-way Exposed Suspended Ceiling Grid System”. Rondo, Auckland, NZ.

American Society for Testing and Materials (2013). “C636/C636M-Standard Practice for Installation of Metal Ceiling Suspension Systems for Acoustical Tile and Lay-in Panels”. PA, USA.

Dhakal RP and MacRae G (2013). “Ceiling Systems Design and Installation Lessons from the Canterbury Earthquakes”. Proceedings of 10th International Conference on Urban Earthquake Engineering (10CUEE), Tokyo Institute of Technology, Tokyo, Japan, 1-2 March 2013.

New Zealand Standard (2004). “NZS 1170.5:2004, Structural Design Actions Part 5: Earthquake actions-New Zealand”. Standards New Zealand, Wellington, NZ.

New Zealand Standard (2009). “NZS 4219:2009, Seismic Performance of Engineering Systems in Buildings”. Standard New Zealand, Wellington, NZ.

New Zealand Standard (2013). “NZS 4541:2013 Automatic fire sprinkler systems”. Standard New Zealand, Wellington, NZ.

Ministry of Works (1985). “PW/81/10/1:1985 – Guidelines for the Seismic Design of Public Buildings: Appendix D Suspended Ceilings and Associated Fittings and Fixtures”. MoW, Wellington, NZ.

Australian/New Zealand Standard (2002). “AS/NZS 1170.1:2002 Structural design actions – Part 1: Permanent, Imposed and Other Actions”. Standards New Zealand, Wellington, NZ.

Australian/New Zealand Standard (1999). “AS/NZS 1530.3:1999 Methods for Fire Test on Building Materials, Components and Structures - Simultaneous Determination of Ignitability, Flame Propagation, Heat Release and Smoke Release”. Standards New Zealand, Wellington, NZ.

Australian Standard (1991), “AS 2946:1991 – Suspended Ceilings, Recessed Luminaires and Air Diffusers – Interface Requirements for Physical Compatibility”. Standards Australia, Sydney, Australia.

American Society of Civil Engineers (1994). “ASCE/SEI 7-10. Minimum Design Loads for Buildings and Other Structures, Vol. 7, Chapter 13: Seismic Design Requirements for Non-Structural Components”. American Society of Civil Engineers, USA.

American Society for Testing and Materials (2013). “C635/C635M- Standard Specification for the Manufacture, Performance, and Testing of Metal Suspension Systems for Acoustical Tile and Lay-in Panel Ceilings”. PA, USA.

American Society for Testing and Materials International (2011). “E1414-11 - Standard Test Method for Airborne Sound Attenuation Between Rooms Sharing a Common Ceiling Plenum (Two room method)”. PA, USA.

Ceilings and Interior Systems Construction Association CISCA (2004). “Guidelines for Seismic Restraint for Direct Hung Suspended Ceiling Assemblies, Seismic Zones 3-4”. Ceiling and Interior Systems Construction Association, Illinois, USA.

Armstrong (2013). “Seismic Design Guide New Zealand Version, Suspended Ceiling Systems”. Armstrong, Auckland, New Zealand.

Dhakal RP, MacRae GA and Hogg K (2011). “Performance of Ceilings in the February 2011 Christchurch Earthquake”. Bulletin of the New Zealand Society for Earthquake Engineering, 44(4): 379-389.

Stuff (2014). http://www.stuff.co.nz/dominion-post/business/commercial-property/9209910/Long-wait-for-BNZ-workers

ANCO Engineers Inc. (1983). “Seismic Hazard Assessment of Non-Structural Ceiling Components: Phase I”. Report No. 1249.12, Grant 8114155, National Science Foundation, Culver City, California, USA.

Rihal SS and Granneman G (1984). “Experimental Investigation of the Dynamic Behavior of Building Partitions and Suspended Ceilings during Earthquakes”. Report No. ARCE R-84-1, California Polytechnic State University, San Luis Obispo, California, USA.

Badillo-Almaraz H, Whittaker AS and Reinhorn AM (2007). “Seismic Fragility of Suspended Ceiling Systems”. Earthquake Spectra, 23(1): 21–40. DOI: https://doi.org/10.1193/1.2357626

Gilani AS, Reinhorn AM, Glasgow B, Lavan O and Miyamoto HK (2010). “Earthquake Simulator Testing and Seismic Evaluation of Suspended Ceilings”. Journal of Architectural Engineering, 16(2): 63-73. DOI: https://doi.org/10.1061/(ASCE)1076-0431(2010)16:2(63)

Gilani AS, Takhirov Sh And Tedesco L (2012). “Seismic Evaluation Procedure for Suspended Ceilings and Components, New Experimental Approach”. Proceedings of the 15th World Conference on Earthquake Engineering, Lisbon, Portugal, 20-24 September 2012.

Glasgow B, Gilani AS and Miyamoto HK (2010). “Resilient Suspended Ceilings for Sustainable Design of Buildings”. Proceedings of Structures Congress, Orlando, Florida, USA, 12-15 May 2010. DOI: https://doi.org/10.1061/41130(369)232

Ryu KP, Reinhorn AM and Filiatrault A (2013). “Capacity Evaluation of Suspended Ceiling Systems”. Technical Report MCEER-13-XXXX, Buffalo, NY, USA.

Paganotti G (2010). “Behaviour of Suspended Ceiling System during Seismic Events: Development of Fragility Curves”. Masters Thesis, Politecnico Di Milano, Italy.

Paganotti G, MacRae GA and Dhakal RP (2011). “Development of Typical NZ ceiling System Seismic Fragilities”. Proceedings of the Ninth Pacific Conference on Earthquake Engineering, Building an Earthquake-Resilient Society, Auckland, NZ, 14-16 April 2011.

Pourali A, Dhakal RP, MacRae GA and Tasligedik AS (2015). “Shake Table Tests of Perimeter-Fixed Type Suspended Ceilings”. Proceedings of NZ Society for Earthquake Engineering NZSEE Conference, Rotorua, NZ, 10-12 April 2015.

Singh J, MacRae GA, Dhakal RP and Pampanin S (2011). “Building Seismic Ceiling Fragility using Spectral Acceleration”. Proceedings of the Ninth Pacific Conference on Earthquake Engineering: Building an Earthquake-Resilient Society, Auckland, NZ, 14-16 April 2011.

Published
2016-03-31
How to Cite
Dhakal, R. P., MacRae, G. A., Pourali, A., & Paganotti, G. (2016). Seismic fragility of suspended ceiling systems used in NZ based on component tests. Bulletin of the New Zealand Society for Earthquake Engineering, 49(1), 45-63. https://doi.org/10.5459/bnzsee.49.1.45-63
Section
Articles

Most read articles by the same author(s)

1 2 3 > >>